HP HP0-207 시험문제

IT업계에 종사하시는 분들은 IT인증시험을 통한 자격증취득의 중요성을 알고 계실것입니다. ITExamDump에서 제공해드리는 인증시험대비 고품질 덤프자료는 제일 착한 가격으로 여러분께 다가갑니다. ITExamDump덤프는 IT인증시험에 대비하여 제작된것으로서 높은 적중율을 자랑하고 있습니다.덤프를 구입하시면 일년무료 업데이트서비스, 시험불합격시 덤프비용환불 등 퍼펙트한 서비스도 받을수 있습니다.

ITExamDump 에서는 IT인증시험에 대비한 퍼펙트한HP 인증HP0-207덤프를 제공해드립니다. 시험공부할 시간이 충족하지 않은 분들은ITExamDump 에서 제공해드리는HP 인증HP0-207덤프로 시험준비를 하시면 자격증 취득이 쉬워집니다. 덤프를 구매하시면 일년무료 업데이트서비스도 받을수 있습니다.

ITExamDump 는 완전히 여러분이 인증시험 준비와 안전한 시험패스를 위한 완벽한 덤프제공 사이트입니다.우리 ITExamDump의 덤프들은 응시자에 따라 ,시험 ,시험방법에 따라 알 맞춤한 퍼펙트한 자료입니다.여러분은 ITExamDump의 알맞춤 덤프들로 아주 간단하고 편하게 인증시험을 패스할 수 있습니다.많은 it인증관연 응시자들은 우리 ITExamDump가 제공하는 문제와 답으로 되어있는 덤프로 자격증을 취득하셨습니다.우리 ITExamDump 또한 업계에서 아주 좋은 이미지를 가지고 있습니다.

우리ITExamDump에서는 끊임없는 업데이트로 항상 최신버전의HP인증HP0-207시험덤프를 제공하는 사이트입니다, 만약 덤프품질은 알아보고 싶다면 우리ITExamDump 에서 무료로 제공되는 덤프일부분의 문제와 답을 체험하시면 되겠습니다, ITExamDump 는 100%의 보장 도를 자랑하며HP0-207시험은 한번에 패스할 수 있는 덤프입니다.

ITExamDump의HP인증 HP0-207덤프의 인지도는 아주 높습니다. 인지도 높은 원인은HP인증 HP0-207덤프의 시험적중율이 높고 가격이 친근하고 구매후 서비스가 끝내주기 때문입니다. ITExamDump의HP인증 HP0-207덤프로HP인증 HP0-207시험에 도전해보세요.

시험 번호/코드: HP0-207
시험 이름: HP (Procurve Adaptive EDGE Fundamentals)

연구결과에 의하면HP인증 HP0-207시험은 너무 어려워 시험패스율이 낮다고 합니다. ITExamDump의 HP인증 HP0-207덤프와 만나면HP인증 HP0-207시험에 두려움을 느끼지 않으셔도 됩니다. ITExamDump의 HP인증 HP0-207덤프는 엘리트한 IT전문가들이 실제시험을 연구하여 정리해둔 퍼펙트한 시험대비 공부자료입니다. 저희 덤프만 공부하시면 시간도 절약하고 가격도 친근하며 시험준비로 인한 여러방면의 스트레스를 적게 받아HP인증 HP0-207시험패스가 한결 쉬워집니다.

HP0-207 덤프무료샘플다운로드하기: http://www.itexamdump.com/HP0-207.html

NO.1 While examining the spanning tree configuration on a ProCurve switch, you notice that one of
the ports is in the Blocking state. Which statement describes how this port will function in this
state?
A.The port is completely blocked for all purposes.
B.The switch will not forward user traffic through that port, but will forward telnet traffic.
C.The switch will not forward user traffic through that port, but will forward BPDUs through that port.
D.The switch forwards user traffic through that port, but does not receive user traffic through that port.
Correct:C

HP시험문제   HP0-207   HP0-207자격증

NO.2 What are the key principles of the Adaptive EDGE architecture? Select TWO.
A.Control to the Edge
B.Control to the Desktop
C.Command from the Center
D.Management from Anywhere
E.Security throughout the Network
Correct:A C

HP시험문제   HP0-207   HP0-207자격증

NO.3 You configured Rapid Spanning Tree Protocol on four ProCurve Switch 5348xl switches at a
customer site. During the configuration, you forgot to configure the switches so that
switch-to-switch links are not defined as edge ports. Which statement describes the consequence
of your oversight?
A.The switches in the spanning tree will elect multiple Root bridges.
B.The switches will reject the spanning tree configuration and block all ports until the configuration is
corrected.
C.The switches will be unable to elect a Root bridge and will not be able to forward traffic until the
configuration is corrected.
D.The switches will require more time to elect the Root bridge and resolve the topology, but the spanning
tree will otherwise function normally.
Correct:D

HP시험문제   HP0-207   HP0-207자격증

NO.4 You are about to update the software on a ProCurve switch. Which command do you use to view
a list of all software versions stored on the switch?
A.show run
B.show flash
C.show startup
D.show version
Correct:B

HP시험문제   HP0-207   HP0-207자격증

NO.5 What are the primary solution categories of the Adaptive EDGE Architecture? Select THREE.
A.mobility
B.security
C.reliability
D.availability
E.upgradeability
F.convergence
G.cost-effectiveness
Correct:A B F

HP시험문제   HP0-207   HP0-207자격증

NO.6 You are implementing a fully connected HP Switch Mesh at a customer site. Which statement
describes a valid design guideline for HP Switch Meshing?
A.A switch may be connected to no more than four mesh domains.
B.Up to five Switch 5400zl Series switches can be included in a full mesh.
C.All links in a full mesh must operate at the same speed and use the same media type.
D.When a switch is configured for HP Switch Meshing protocol, all of the ports on that switch must
participate in the mesh.
Correct:B

HP시험문제   HP0-207   HP0-207자격증

NO.7 You have been asked to configure IGMP on a ProCurve Switch 6200yl at a customer site. What
are the steps for enabling IGMP on the switch?
A.Enter the manager level, then issue the ip igmp command.
B.Enter the global configuration context, then issue the ip igmp command.
C.Enter the VLAN context for each VLAN that will support IGMP, then issue the ip igmp command.
D.Enter the interface configuration context for each port configured with a VLAN, then issue the ip igmp
command.
Correct:C

HP시험문제   HP0-207   HP0-207자격증

NO.8 You are assigned to configure ProCurve switches at a customer site for in-band management.
Which are in-band management methods? Select TWO.
A.Telnet
B.SNMP
C.XMODEM
D.serial console
E.menu interface
Correct:A B

HP시험문제   HP0-207   HP0-207자격증

NO.9 You are configuring a ProCurve Layer 2 switch to obtain time information from an SNTP server
located on a different IP network than the switch. Which configuration steps are necessary on the
switch to enable this functionality?
A.The switch cannot be configured to obtain time information from a server on a different IP network.
B.Define a default gateway for the switch, enable SNTP, use the sntp server command to enter the IP
address of the server.
C.Assign a port on the switch to a VLAN that includes the SNTP server, enable SNTP, configure the
switch for SNTP unicast mode.
D.Configure an IP address on the same IP network as the SNTP server, enable TimeP, configure the
switch for SNTP broadcast mode.
Correct:B

HP시험문제   HP0-207   HP0-207자격증

NO.10 You must update the software on a customer's ProCurve Switch 5412zl. Which statement
correctly describes the process for this operation? Select TWO.
A.Use TFTP for direct serial transfer of the software.
B.Use FTP for in-band transfer of the software through an IP network.
C.Use TFTP for in-band transfer of the software through an IP network.
D.Transfer the software from your workstation using a direct serial transfer.
E.Instruct the switch to search for any available TFTP server without knowing its IP address.
Correct:C D

HP시험문제   HP0-207   HP0-207자격증

NO.11 On switches that support the Switch Setup screen interface, which parameters can be
configured on the Switch Setup screen? Select TWO.
A.STP bridge priority
B.IP address of the TACACS+ server
C.system name and contact information
D.IP address and subnet mask for each VLAN
E.IP address and subnet mask for the default VLAN
Correct:C E

HP시험문제   HP0-207   HP0-207자격증

NO.12 At a customer site, you have configured four ProCurve switches for HP Switch Meshing and
Multiple Spanning Tree Protocol. How will the mesh appear to non-mesh switches in the same
spanning tree domain?
A.as a single device
B.as a set of devices without redundant links
C.as devices that cannot participate in the spanning tree
D.as a set of devices with spanning tree enabled to block redundant links
Correct:A

HP시험문제   HP0-207   HP0-207자격증

NO.13 You are about to configure HP Switch Meshing on four ProCurve switches at a customer site.
All of the ports that will be included in the mesh are configured for membership in customer
VLANs. How will the mesh configuration affect the VLAN configuration?
A.The mesh ports will automatically become a tagged member of all configured VLANs.
B.The mesh ports will not be a member of any VLANs until you manually configure its VLAN assignments.
C.The mesh ports will not be 802.1Q-compliant and will only be able to retain membership in a single
untagged VLAN.
D.The mesh ports will automatically become a member of the default VLAN and must be configured for
other VLAN membership.
Correct:A

HP시험문제   HP0-207   HP0-207자격증

NO.14 A customer is planning a Power over Ethernet deployment for a large call center that will use
VoIP telephones. While planning the wiring closets for the deployment, the customer suggests
using the uplink ports of a ProCurve Switch 2650-PWR to provide power to a ProCurve Switch
2600-8-PWR. Which statement describes a correct response to this suggestion?
A.It is only possible if the second switch is a ProCurve Switch 2626-PWR.
B.It is not possible because the 2600-8-PWR cannot act as a Powered Device.
C.It is only possible if the customer adds a ProCurve 600 EPS/RPS to the first switch.
D.It is not recommended because the second switch will not have adequate power redundancy.
Correct:B

HP시험문제   HP0-207   HP0-207자격증

NO.15 While using the CLI to configure a ProCurve switch, you must change context from the manager
level to the global configuration level. Which command do you use?
A.exit
B.write
C.global
D.enable
E.configure
Correct:E

HP시험문제   HP0-207   HP0-207자격증

NO.16 You must remotely manage a customer's switch using Telnet. Which configuration/monitoring
interfaces are available? Select TWO.
A.web interface
B.menu interface
C.ProCurve Manager
D.boot monitor interface
E.command line interface
Correct:B E

HP시험문제   HP0-207   HP0-207자격증

NO.17 You are installing a ProCurve switch at a customer site and must enable remote management
for network administrators. Which configuration parameter is necessary to ensure that
administrators can manage the switch even if they are on different IP networks?
A.default VLAN
B.default gateway
C.default password
D.default management profile
Correct:B

HP시험문제   HP0-207   HP0-207자격증

NO.18 How is traffic prioritization accomplished with IEEE 802.1p?
A.802.1Q-compliant devices enforce priorities based on VLAN ID.
B.802.1Q-compliant devices set one of 8 values in a 3-bit field in the VLAN tag.
C.802.1Q-compliant devices set one of 64 values in a 6-bit field in the IP datagram header.
D.802.1Q-compliant devices dedicate a portion of available bandwidth to each prioritized conversation.
Correct:B

HP시험문제   HP0-207   HP0-207자격증

NO.19 While using the CLI to configure a ProCurve switch, you must move from the global
configuration level to the port context configuration level for port a1. Which command do you use?
A.port a1
B.ethernet a1
C.interface a1
D.configure a1
Correct:C

HP시험문제   HP0-207   HP0-207자격증

NO.20 How do ProCurve switches, configured with link aggregation (also known as port trunking),
handle broadcast traffic?
A.Broadcast traffic is flooded through all of the ports in the trunk.
B.The switch sends a query and receives permission from potential receivers before flooding.
C.Broadcast traffic is handled in exactly the same way it would be without port trunking configured.
D.Broadcast traffic is flooded through non-trunked ports, but forwarded only through one of the ports in
the trunk.
Correct:D

HP시험문제   HP0-207   HP0-207자격증

ITExamDump 제공 HP HP0-207시험덤프자료가 광범한 시험준비인사들의 찬양을 받은지 하루이틀일이 아닙니다.이렇게 많은 분들이ITExamDump 제공 HP HP0-207덤프로 시험을 통과하여 자격증을 취득하였다는것은ITExamDump 제공 HP HP0-207덤프가 믿을만한 존재라는것을 증명해드립니다. 덤프에 있는 문제만 열심히 공부하시면 시험통과 가능하기에 시간도 절약해줄수있어 최고의 믿음과 인기를 받아왔습니다. HP HP0-207 시험을 봐야 하는 분이라면ITExamDump를 한번 믿어보세요. ITExamDump도움으로 후회없이 멋진 IT전문가로 거듭날수 있을것입니다.